Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Albany Homeowners
The gap between a fireplace that drafts well and one that smokes into the room or smells of creosote in July is usually a defect you can’t see: a cracked flue tile, a crown that has pulled away from the stack, flashing that lifted during a freeze-thaw cycle. Chimney repair in Albany starts with finding that defect and proving it on camera before anyone quotes a fix. Our technicians have up to experience working on the older masonry stacks and mid-century liners common in this city, and we carry the trade-grade materials – HeatShield, DuraFlex, Copperfield, Gelco – that hold up in a climate that swings from humid summers to hard freezes. We’re state-licensed and insured, and we put what we find on a photo report you keep. Call (866) 650-9028 to book an assessment; estimates are free and the written quote sets the final price.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a covered, screened cap over the flue opening to keep rain, snow, squirrels, and birds out while letting smoke and gases escape. You need one when the flue is open to the sky – which is most Albany chimneys that have never been capped – or when an existing cap has rusted through or blown loose. We fit Copperfield and Famco caps sized to the actual flue, sealed to the crown so water runs off rather than in. Typical installed cost in Albany runs $250 to $650 depending on flue count and cap style; the free written estimate confirms the figure before we order anything.
Why Caps Matter in a Heating Climate
An open flue takes in meltwater and snow all winter, and every wet-freeze cycle works on the mortar and tile below. A cap also stops downdrafts that push smoke back into the room on gusty days. The screen keeps nesting animals from blocking the flue, which is a carbon monoxide concern, not just a nuisance.
Stainless and Powder-Coated Choices
Stainless caps outlast painted steel by a wide margin in this region, and the difference in price is small. Powder-coated finishes suit homeowners matching a roof or trim color. We’ll explain both and let the chimney decide – tall stacks and multi-flue setups need different bracing.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement means pulling a failed cap and fitting a new one, and it usually comes up when a cap has rusted at the seams, lost its screen, or been bent out of shape by wind and ice. A cap that no longer seals lets water straight into the flue, so this is one of the few repairs where waiting has a real cost. We remove the old unit, check the crown and flue top for damage the cap was hiding, and install a properly sized Copperfield or Famco replacement. Expect roughly $250 to $650 installed, with the exact number on the written estimate once we see the flue.
Rust and Seam Failure
Painted steel caps in this climate tend to rust first along the welded seams and at the mounting legs. Once a seam opens, water tracks down the inside of the flue rather than shedding off. If you see rust streaks on the stack, the cap is worth a look.
Reusing Sound Hardware
Some caps are fine and only the fasteners or the screen have failed. We’ll say so plainly and repair what’s serviceable instead of selling a full replacement. Nothing gets replaced without a photo you can see.
Chimney Liner Installation
Chimney Liner Installation is putting a new flue liner inside the chimney to carry smoke and gases safely to the top, and it’s needed when the original clay tiles are cracked, spalled, or missing, or when an appliance needs a flue sized to it. A compromised liner lets heat and carbon monoxide reach the framing and living space, so this is a repair we don’t put off once it’s documented. We install DuraFlex flexible liner systems, which handle the offsets and irregular flues common in Albany’s older homes far better than rigid pipe. Full relining typically runs $2,500 to $6,000 depending on height and liner diameter; the written estimate fixes the price.
When Resurfacing Beats Relining
If the tiles are intact but the joints are eroded, HeatShield ceramic resurfacing can restore the flue without a full liner. It’s a specialized system most generalist outfits don’t carry. We only recommend it when the camera shows it will hold.
Sizing the Flue to the Appliance
A wood stove or gas insert needs a flue matched to its output or it won’t draft cleanly. We size the liner to the appliance, not to whatever pipe is convenient. Olympia Chimney components round out the connection hardware where needed.
Chimney Flashing Repair
Chimney Flashing Repair fixes the metal and sealant that join the chimney to the roof, and it’s the repair Albany homeowners most often need without knowing it – flashing is where most roof leaks around a chimney start. You need it when you see water staining on the ceiling near the stack, rusted or lifted flashing, or gaps where the sealant has dried and pulled away. We reset or replace the flashing, work it into the shingles properly, and seal the joints. Typical cost runs $300 to $900 depending on roof pitch and how much flashing has to be rebuilt; the written estimate confirms it.
Freeze-Thaw and Sealant Failure
Albany’s winters open and close sealant joints by turns, and urethane that looked fine in fall can be split by spring. That’s why we look at flashing on every inspection rather than only when a leak is reported. Catching it early keeps water out of the framing.
Step and Counter Flashing
Proper flashing is two layers: step flashing woven into the shingles and counter flashing cut into the masonry. When only the counter flashing is redone, the leak often returns. We build both.
Chimney Crown Repair
Chimney Crown Repair addresses the concrete or mortar cap at the very top of the stack – the surface that sheds water away from the flue. A cracked or crumbling crown lets water soak into the masonry and freeze, which is the single most common cause of a chimney failing from the top down. We rebuild crowns with a proper overhang and slope, seal the flue-to-crown joint, and cure the work so it holds season to season. Crown repair in Albany generally runs $400 to $1,200 depending on stack size and how much has to be rebuilt; the free estimate sets the figure.
Cracks That Let Water In
Hairline cracks widen with each freeze, and once water gets behind the crown it works down into the tiles and mortar joints. A crown that sheds water properly protects everything below it. That’s why we check it before quoting any liner work.
Rebuilding Rather Than Patching
A smeared patch over a failed crown usually cracks again within a season. We form a new crown with the right slope and overhang so it does its job. Where the whole top course is loose, we rebuild it so the crown has something solid to sit on.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they can actually do, and choosing one matters more than the price difference between them – a company that can sweep and inspect but has to subcontract the liner work leaves you coordinating two parties. What you want is one team that diagnoses, quotes, and performs the repair, with the photo evidence to back the recommendation. At Chimney Sweep Albany, the same technicians who inspect the chimney do the repair, so nothing gets lost between the inspection and the fix. Costs run across our full repair range, roughly $250 for a cap up to $6,000 for a full reline; the written estimate is the final word.
What to Ask Before You Book
Ask whether the company performs the repair in-house or subs it out, and whether you’ll get a camera report. Ask which liner and cap brands they install – trade-grade names like DuraFlex and Copperfield tell you they’re sourcing professionally. And ask for the estimate in writing before work starts.
Reading the Camera Report
Anyone can say your liner is cracked. A photo or video of the actual defect, shown to you before the recommendation, is the difference between a diagnosis and a sales pitch. Insist on it, and walk away from anyone who won’t provide it.
Chimney Masonry Repair
Chimney Masonry Repair covers the brick, mortar, and stonework of the stack itself – repointing crumbling joints, replacing spalled bricks, and rebuilding sections that have pulled away from the house. You need it when mortar is washing out, bricks are flaking or loose, or the stack is leaning or separating. Left alone, masonry damage lets water in and can eventually compromise the chimney’s structure. We repoint with mortar matched to the original so the repair doesn’t trap moisture, and we replace damaged brick from the top down. Masonry repairs typically run $500 to $3,000 depending on the extent; the free written estimate settles it.
Repointing Versus Rebuilding
Repointing – grinding out failed mortar and packing fresh material into the joints – fixes most weathering damage. Rebuilding is for when the bricks themselves have failed or the stack has moved. We tell you which one the chimney actually needs.
Mortar Matched to the Brick
Hard modern mortar against soft old brick causes spalling, so matching the mix to the original matters. We take the time to get it right. Done properly, repointing holds for decades.
Brands We Service
We work with the professional chimney-industry brands because that’s what holds up on a real Albany stack. DuraFlex flexible liner systems are what we reach for on older, offset, or irregular flues where rigid pipe won’t seat cleanly – they flex to the chimney’s shape and stay code-compliant. HeatShield is our ceramic resurfacing system for flues with eroded joints but sound tiles, a repair that restores the flue without a full reline. Copperfield and Famco supply the caps, dampers, and venting hardware that finish a job properly, and Gelco covers the crown and masonry side. We service this equipment and know where each brand wears and where it holds.
Whether you have DuraFlex, HeatShield, Copperfield, Famco, or Gelco components already installed, or any other make, we can help. If a previous install needs correcting, we’ll show you what’s wrong on camera before we quote the fix.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke rolling back into the room. This often points to a blocked or undersized flue, or a failing liner. It’s a draft problem with a real cause, and it’s worth diagnosing before you light another fire.
- A creosote smell in warm weather. That sour, tarry odor means creosote has built up and is reacting to heat and humidity. It’s a sign the flue needs cleaning and a look at the liner.
- Water staining or damp masonry. Streaks on the stack or water on the ceiling near the chimney usually mean flashing or crown failure. Water and freeze-thaw will keep damaging the masonry until it’s fixed.
- Crumbling mortar or loose bricks. When joints wash out or bricks flake, the structure is losing integrity. Have it looked at before it spreads and the repair gets bigger.
- Rust on the damper or cap. Rust inside the firebox or on the cap points to water getting in from above. The source is almost always the crown, cap, or flashing.
Our Process, Step by Step
- 1
Book the visit. Call (866) 650-9028 and we’ll schedule an assessment. We answer 24/7, with fast dispatch from 7am to 7pm for the technician visit.
- 2
Inspect with a camera. We run a camera down the flue and check the firebox, damper, crown, cap, flashing, and masonry from the roof. Everything gets documented.
- 3
Show you the findings. You see the photos and video of the actual defects before we recommend anything. That’s the whole point of the camera – evidence you can judge for yourself.
- 4
Quote in writing. We lay out the options and the cost per job on a written estimate. If a repair can safely wait, we say so; nothing gets recommended without a documented reason.
- 5
Do the repair and confirm it. The same team that inspected does the work, using trade-grade materials, then re-checks the result and leaves you with the documentation.
How Much Does Chimney Repair Cost in Albany?
Chimney repair in Albany depends heavily on what’s actually wrong, which is why a written estimate beats a phone guess. A typical cap installation or replacement runs $250 to $650 installed. Flashing repair runs $300 to $900, and crown repair runs $400 to $1,200 depending on stack size. Masonry repointing or brick replacement typically runs $500 to $3,000 based on how much of the stack has failed. A full liner installation is the largest job, generally $2,500 to $6,000 depending on chimney height and liner diameter.
What moves the price: chimney height and roof access, how many flues are involved, whether the damage is cosmetic or structural, and whether a previous repair has to be undone first. You avoid overpaying by getting the camera evidence up front and comparing the written scope, not just the total. Every estimate we give is free, itemized, and shows what’s included – materials, labor, and the follow-up check. If part of the job can wait a season without risk, we’ll tell you, and the estimate will reflect only what needs doing now. The written estimate sets the final price; there’s no surprise on the invoice.
Our Service Area Near Albany
We work throughout Albany and the surrounding communities, including Loudonville, Menands, Westmere, Colonie, Latham, Watervliet, East Greenbush, Rensselaer, Hampton Manor, and Roessleville. Scheduling is straightforward – we book an assessment, dispatch a technician from 7am to 7pm, and answer the phone around the clock. If you’re nearby and need chimney repair or an inspection, we can get you on the schedule. Travel within the area is routine, so response is quick once a visit is booked.
Homeowners in Voorheesville and the outlying towns are covered too; see our chimney repair page for that area, or start with a Chimney Sweep Albany assessment if you’re not sure yet what the chimney needs.
Serving Albany, NY – Our Local Coverage Area
We serve Albany and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Albany
Chimney repair is the work of fixing the parts of a chimney that have failed or worn – the liner, crown, cap, flashing, masonry, or damper – so it vents smoke and gases safely and keeps water out. It’s distinct from sweeping, which removes creosote, and from inspection, which finds the problems in the first place. A repair follows a diagnosis with evidence. Call (866) 650-9028 for a free estimate on any repair.
Most repairs take a few hours to a day – a cap or flashing fix is usually a single visit, while crown and masonry work can take longer depending on scope. A full liner installation typically runs one to two days. We give you a realistic timeframe with the written estimate. Call (866) 650-9028 to book and we’ll confirm the schedule.
Repairs range from about $250 for a cap up to roughly $6,000 for a full liner installation, with flashing, crown, and masonry work falling in between. The exact price depends on what the camera shows and how much has to be rebuilt. Every estimate is free and in writing, and that written figure sets the final price. Call (866) 650-9028 for an exact quote – estimates are free.
Yes – we install and service DuraFlex flexible liner systems, along with HeatShield, Copperfield, Famco, and Gelco components. DuraFlex is what we use on offset and irregular flues where rigid pipe won’t fit cleanly. If you have an existing DuraFlex install that needs checking, we’ll inspect it on camera. Call (866) 650-9028 to schedule.
Same-day repair is often possible when you call early and we have an opening. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside those hours is booked into the next opening. Call (866) 650-9028 to check availability.
Yes – our workmanship and the manufacturer-backed hardware we install carry warranty coverage, and the terms are spelled out on your written estimate. The brands we use – Copperfield, Famco, DuraFlex, Gelco, HeatShield – back their products. You’ll know exactly what’s covered before we start. Call (866) 650-9028 with questions about coverage.
Clear access to the fireplace and hearth, move anything breakable away from the work area, and make sure we can get to the roof or the chimney from outside. If you have an older appliance manual or records of past work, have them handy. That’s usually all it takes. Call (866) 650-9028 if you’re unsure what to do.
Schedule Your Chimney Repair Service in Albany Today
Don’t wait for the next freeze to find out what’s wrong up there. Call (866) 650-9028 to book a chimney repair assessment in Albany – we answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get camera evidence, a written estimate, and a no-obligation price. Licensed and insured, with trade-grade materials and a repair done right. Estimate first, and if the work can wait, we’ll tell you.
Written by the team at Chimney Sweep Albany.